ADATAを接続してみる

Cubieez 0.1 RC2 (A20 version) でもつなげるだけで、認識されました。

root@cubieez:~# lsb_release -a
No LSB modules are available.
Distributor ID: Debian
Description: Debian GNU/Linux 7.1 (wheezy)
Release: 7.1
Codename: wheezy
root@cubieez:~# uname -a
Linux cubieez 3.3.0+ #1 SMP PREEMPT Sat Jul 20 11:39:49 CEST 2013 armv7l GNU/Linux
root@cubieez:~#

 

root@cubieez:~# dmesg |grep -i sd
[ 2.906210] [mmc-msg] sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.916365] [mmc-msg] sdc0 Probe: base:0xf003c000 irq:64 sg_cpu:ffdf5000(4fc00000) ret 0.
[ 4.400709] [mmc-msg] sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.409669] [mmc-msg] sdc0 power on
[ 4.430692] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.522580] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.534380] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.566127] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.575566] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.587360] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 4.623116] [mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 4.632463] [mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B
[ 4.697070] [mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B
[ 4.706611] mmc0: new high speed SDHC card at address 59b4
[ 4.712923] mmcblk0: mmc0:59b4 USD 29.4 GiB
[ 12.943889] ata1.00: ATA-8: ADATA SSD S510 120GB, 3.3.2, max UDMA/133
[ 12.971889] scsi 0:0:0:0: Direct-Access ATA ADATA SSD S510 1 3.3. PQ: 0 ANSI: 5
[ 12.983112] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 12.991753] sd 0:0:0:0: [sda] Write Protect is off
[ 12.996578] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.006216] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.020837] sda: sda1
[ 13.029234] sd 0:0:0:0: [sda] Attached SCSI disk
root@cubieez:~#

 

root@cubieez:~# fdisk -l /dev/sda

WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted.

Disk /dev/sda: 120.0 GB, 120034123776 bytes
255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x49e2fd2f

Device Boot Start End Blocks Id System
/dev/sda1 1 234441647 117220823+ ee GPT
root@cubieez:~#

 

root@cubieez:~# hdparm -T -t /dev/sda1

/dev/sda1:
 Timing cached reads: 820 MB in 2.00 seconds = 409.56 MB/sec
 Timing buffered disk reads: 312 MB in 3.06 seconds = 101.99 MB/sec